Tuesday, October 25, 2011

What is the best way to replace a window pane in a home window without taking the window out?

We have a cracked window pane in a 2 pane sliding window in an old house. We want to be able to replace the pane, but don't know how to get the window out of the tracks, so we want to replace the pane in place.What is the best way to replace a window pane in a home window without taking the window out?Look at it carefully. Get some thick gloves. Then tap on the glass gently with your knuckles to listen for a dull thud. When no one is looking, pick up a hammer and beat the shti outta the glass until you can't see any cracks anymore.What is the best way to replace a window pane in a home window without taking the window out?if its a double pane window they are sealed from air to keep moister out. you would have to take it out its really not that big of a job. if it is single pane is probably glazed in you cut the glazing out and window should come out replace with new glass and reglaze / glazing looks like puttyWhat is the best way to replace a window pane in a home window without taking the window out?Call the Glass Doctor, he should know what to do.

How can I replace fluid in a leaking glitter lamp?

I have an original glitter lamp from the 1960's. The lamp is leaking out of the perished seal and there is about 5cm missing.

I want to replace the missing fluid but don't know what it is.How can I replace fluid in a leaking glitter lamp?Usually water

http://en.wikipedia.org/wiki/Lava_lamps

How do you replace the alternator on a '93 Subaru Legacy?

My battery light and brake lights are coming on after driving a few minutes. I had it check out for free at Advance Auto parts and it is reading good! Would i also need to replace the belt since i feel some sliping? If , so how or where to find an online guide? Thanks in advance.How do you replace the alternator on a '93 Subaru Legacy?start the engine... disconnect the positive battery cable, if the engine dies, the alternator is bad. remove and replace, including the belt, then hook the positive battery cable back up.How do you replace the alternator on a '93 Subaru Legacy?If you are planning on doing the work yourself, get a good manual for the car (Haynes or one like it) at the parts store. It is not all that difficult. I would recommend replacing the belt if it has been slipping as it would have been worn more than usual.

How can I replace the wooden door sill underneath my front door?

I have a raised porch. The door sill underneath the front door is rotting and I would like to replace it. How can I remove the door sill? Do I have to take the door down and all sides and additional pieces? What kind of wood do you recommend and do I get a 2x4 or 2x6?How can I replace the wooden door sill underneath my front door?All the charm of and old house.

Most of the ones I have worked on were made of oak. A few were southern yellow pine, but they were produced when old growth timber was still available. The threshold will be one piece, so you will need to get something just as wide and thick or do a glue-up to match. The door jambs are rabbeted to accept the threshold and nailed in from the side of the jamb. You could replace it without removing the entire jamb but will need to shim under the new one to keep it tight to the top of the rabbets.

If its not too rotted you might want to consider and exterior grade wood filler and repaint it. Good luck with the project.
  • acne on back shoulders
  • get liquid foundation
  • How much does it cost to replace underground water pipe?

    Our underground water pipe is 275 feet long and leaks closing to the water meter. What is the reasonable price to replace the whole 275 feet water pipe? The pipe leaked 6 years ago and previous owner spent $3489 just replaced the leaked part with copper. Currently we have plumber estimate as $9800 by using directional boring. Not quite sure if it is reasonable.How much does it cost to replace underground water pipe?City or State code plays a factor here. Flexible K copper is not cheap plus some states require the line to be 8 feet deep. If you have old black pipe or galvanized pipe, yes you should replace the whole thing. If you can have it 3 feet deep then you can do this your self and pay a plumber to hook it up. Save big bucks. Contact your City on there requirements. Plumbing store for the copper. Rental store for a ditch witch to dig a trench. Plumber to tie in all of your fittings and to the meter. Under ground requires a flaired fitting to connect the copper lines.



    But for a plumber to do the job for under $36.00 per foot seems like a great price to me. It would be a great deal more here in Ohio.How much does it cost to replace underground water pipe?There are some good suggestions here and for small bores it certainly is possible to do it yourself, but always remember to not assume anything, call for utility locates before you dig! http://www.we-bore-it.com

    Report Abuse

    How much does it cost to replace underground water pipe?You are probably paying and extra $3,000 to have the directional boring done, is there a reason your not just doing it in an open trench?How much does it cost to replace underground water pipe?Do it yourself you can rent trenchers at HD or Lowes to go under sidewalks just push a pipe on the end of a hose with water runing through it. if you have to go under a wide driveway just use longer pipe.Or if you don't want to mess with it pick up some day laborers and give them each a shovel.Its not rocket science.How much does it cost to replace underground water pipe?I live in iowa and my water co. charges 11 dollars a ft.

    How do you replace the headlight unit on a 96 ford contour?

    The headlight unit is cracked and I'm trying to replace the whole thing but I don't know where to start to remove the old one.How do you replace the headlight unit on a 96 ford contour?Well, take a look at the new assembly.



    Have a look at where the bolt holes are and locate them on the old headlight assembly.



    You may need to remove the bumper, or disconnect it on one side to get to them all properly.



    Take your time, and dont rush into it.How do you replace the headlight unit on a 96 ford contour?get a chevy

    How do I replace the wiring on a Pfaff 130 sewing machine motor?

    I've removed the motor from the machine, and removed the two long screws that go through the motor, but cannot figure out how to get it open so I can replace the wiring. Help!How do I replace the wiring on a Pfaff 130 sewing machine motor?The bearings on the each end of the shaft are pressed on. Gently pry apart.

    I question if you should be changing out a motor's windings if you don't know how to get it apart.

    How do I replace a steering wheel on a Corsa?

    Bit of bad luck. Someone broke into my car and wrenched off the steering wheel. I have found a second hand one on Ebay but would like to know whether it is easy to replace, or whether this should be done by a mechanic (how to get one to the car is a different question, of course). Thanks.How do I replace a steering wheel on a Corsa?the following link is a database for every service manual, for every car on the road. i use it all the time.

    http://www.bedlib.org/ebsco.html

    (click on the auto repair reference center logo and then navigate with the tabs in the upper right corner when you find your car)How do I replace a steering wheel on a Corsa?I'd replace the Corsa!

    How much does it cost to replace a laptop hard disk in Sydney?

    I've encountered a problem with my hard disk. It occurs that I have to replace that hard disk. So just asking how much does it cost to replace a laptop hard disk. There's one guy offered me $110 for a 250G hard disk. Is the price too high?How much does it cost to replace a laptop hard disk in Sydney?check ebay.com.au for current prices - 2.5%26quot; drives



    replacement can be done yourself. they are easy to swap so dont pay anyone labour as its literally a 2 minute job.
  • programming
  • email
  • How do you replace a dead internal battery in a Roland guitar synth?

    I own a Roland GR30 guitar synth, and the internal backup battery died. Does anyone here know how to replace it?How do you replace a dead internal battery in a Roland guitar synth?It probably comes with a standard CR2032 battery, you can find in watch and department stores. Replacing the battery isn't a issue, just like any other equipment, except that you need to unscrew the GR30 cover until you can see the motherboard and the battery.

    How do you replace a window wiper arm on a car?

    Im not asking how to replace the window wiper blades, but the bracket or the arm that the blades attach to. A piece of debris on the highway flew up and broke one of the arms in half. Im trying to put the wiper arm on the passenger side to the driver side for now. I drive a 2000 Hyundai Elantra.How do you replace a window wiper arm on a car?1. either there is a small set screw on the side of the ball where it rotates. this screw holds it in place.



    2. (ford normally) there should be a small flat lever sticking off to the side of the ball that rotates, pull that out w/ screwdriver or key and that unlocks the arm allowing it to be released.



    3. flip up the end cap (end that rotates), be a plastic cap, and should be a bolt (normally 10mm) that will hold the arm on.



    be care full on all versions not to nick the teeth in the gear as you remove the arm.How do you replace a window wiper arm on a car?It's easy. There is a nut under the housing of the arm. Remove it and the arm slides right off. Slide the new one on, screw the nut back down, replace the housing. Shouldn't take more than 10 mins to replace.

    What is the best way to replace old bricks on a brick house the are broken?

    I am working on an old house that has several broken bricks on it ; these bricks need replacing . I would like to know how to replace them.What is the best way to replace old bricks on a brick house the are broken?you can take a dremel tool and cut out the mortar of the broken brick, then pry it out. then you can lay some new mortar on the bottom and sides, install a new brick, and mortar the top, finishing with whatever mortar finish was already there What is the best way to replace old bricks on a brick house the are broken?Hopefully, you have access to some matching bricks.



    Look around the home, for brick walkways (yard may have grown over them), planters, decorative items, fence posts, mailbox post/enclosure etc... things that may have been made with extra bricks when the home was built. You may get lucky and find some stashed away in storage, in a crawlspace, or attic. By using bricks that came with the original load, to replace broken bricks, repairs will be less obvious.



    Now... before you start replacing bricks, you need to find out WHY you have broken bricks. For example, if some of the bricks broke, in a pattern, and there is a crack in the mortar (especially a staggered crack that runs up at a diagonal), you may have a case where the foundation, or a part of it, has settled. In which case, you should repair that, before repairing the brickwork. If you have a vertical crack near the corner of a wall, it may mean that the bricks (along the side) have pulled loose from the wall, and the home could be at risk of losing a whole section of bricks from the wall, if not attended to.



    Ok, assuming everything that could have caused the brick to break in the first place has been repaired, the basic repair is pretty straightforward... you have to dig out the old brick(s), and mortar, and replace it. Dremel tools with a grinder attachment work pretty good at cutting away the mortar, but you may find an air impact chisel and bit are faster. Remove the mortar from around the broken bricks, and they'll pull right out.

    Clean up the opening as well as you can. Apply new mortar to the bottom of the opening, and the sides, and press the replacement brick in place. You may find a hammer, or mallet, helpful in helping to tap it down into place. (I've used a chisel, or screwdriver...by laying them across the top of the brick, and while holding the handle, tap down gently on the metal. If you lift the handle just a bit, you can actually tap down on the back side of the brick, even though your hammer won't actually reach in there, hehehe. You're using the longer handled tool to apply the force where you want it.) By the way, I like to add just a bit of mortar to the top of the brick, along the back half, just before I work it in place. Then I don't have to squeeze so much in later.

    Don't forget to finish off the mortar like the original work. If its been tooled, you'll need to do it the same. Oh, before you start, make some test mortar to double check the color, and make any changes necessary. (You'll want to clean the old mortar as much as possible first, before comparing colors)



    This is more time consuming than anything else. It's not really 'difficult' to do, if you have the patience, heheh.



    If you'd like to contract the work out though, then look for someone who can do 'tuckpointing'. %26quot;Repairing%26quot; brickwork actually takes more labor than installing new brick, so not all bricklayers would be interested in bidding on the work, but they can tell you who does good work.



    Have FunWhat is the best way to replace old bricks on a brick house the are broken?the best way to remove brick without breaking other brick is to rent a 14 in. in. quickie saw...this will cut deep enough to remove a brick without damaging others...cut the top and bottom bed joints and then chisel out the middle of the brick...now you can chisel the head joints to remove the ends of the brick...What is the best way to replace old bricks on a brick house the are broken?Use drill cut large hole centre of old brick. use drill around edges of old brick before chipping brick out. Do not do the drilling in reverse order.

    How do you replace infiniti g35 coupe headlight assembly?

    I want to replace my reflector mono-xenon headlights on my 04 infiniti g35 coupe with 06 bixenon projector ones. Can anybody help me with it? Thanks.How do you replace infiniti g35 coupe headlight assembly?Remove the front bumper and both inner fender well plastic shields. You will see all the nuts and bolts holding the headlight assys after they are removed.

    How much olive oil needed to replace one egg?

    I heard you can replace things with olive oil in recipes. I am short one egg. About how much olive oil will I need to replace it?How much olive oil needed to replace one egg?what are you making

    if you are backing use apple sauce or

    if you like the taste of bannanas when you are baking then

    you could use 1/4 cup bannana for the egg.



    1 egg should be about 1/4 cup of what ever you substitute for it. I would not use the oil but thats just me.



    good luck.How much olive oil needed to replace one egg?You cannot substitute olive oil for eggs. Tell us the recipe and we can give you a proper alternative ingredient. Hopefully. Just go get eggs.
  • hair extension
  • what is web hosting
  • How do you replace the screen on a blackberry curve 8330?

    I'm wondering how do you replace the screen on the blackberry curve 8330 since I have a crack on it? I am planning on buying a new screen off of ebay but I would like to find out how to take off the original screen so I can get the idea on how to put the new screen on. Hope yall understand what I'm trying to do.How do you replace the screen on a blackberry curve 8330?If your talking of the top screen ( lens cover)then its only glued on all you have to do it pull it off. The new one will have the glue stuff an just press in.



    like this:

    http://www.youtube.com/watch?v=X2G6aVdypHow do you replace the screen on a blackberry curve 8330?search youtube for %26quot;blackberry 8300 screen%26quot;



    http://www.youtube.com/watch?v=iiIl19G74

    How do you replace a 2 prong oulet with a 3 prong?

    In my house I have mostly 2 prong outlets and I would like to replace them with grounded 3 prong outlets. From what I can tell I do not have a ground wire coming into the boxes and the boxes arent connected with EMT, just the wires running from the box downstairs. Its a 100 amp service which is code and I want to avoid running new romex up there to get my ground wire. GFCI breaker?How do you replace a 2 prong oulet with a 3 prong?Lots of wrong answers. As usual. You had the correct one. The national electric code allows you two options. Replace the 2 prong receptacle with another 2 prong receptacle. Or install a GFCI receptacle, (not breaker). You will still not have a ground, but the installation will comply with code and not be unsafe. The alternative is to rewire with a 3 conductor circuit. Ground wires must terminate in your electric panel, not on some pipe or such. A GFCI installed on the first receptacle in the circuit can protect any other receptacles down stream. Don't take electrical advise from untrained people.How do you replace a 2 prong oulet with a 3 prong?Hey there....



    You really need to make sure you have a good ground connection. I think you will probably have to start running new cable....

    I think you have been unlucky as some 2 prong sockets had the box grounded, allthough this may not be up to current standards it is an option.



    Good luck and try not to take any chances.....How do you replace a 2 prong oulet with a 3 prong?You need a ground wire for the third prong. If the outlet boxes are metal, you can run a single wire between them, attach it each one with a screw with a serrated lock washer. Run a pigtail(short piece of wire) between the new three prong outlet ground screw and the box(the ground screw will be painted green). Use green, bare or green with a yellow stripe for the wire. 14 Gauge should be adequate for home wiring. Ground all your outlets to a water or gas pipe using a clamp designed for this. Do not forget to clean the paint from the pipe! If you are not sure that your water or gas pipe are deep and metal, drive a separate ground rod. You also need to tie this back into the ground bar inside your main panel box. Do not tie grounds to neutral together anywhere except in the main panel box.How do you replace a 2 prong oulet with a 3 prong?A GFCI breaker won't provide a ground.

    %26quot;Just wires running from the box downstairs%26quot;??????

    Do you see the wiring anywhere except inside the box.

    If the house is old, and the boxes are steel, there's a very good chance that they were wired with armored cable, ('BX'), the jacket of which is grounded.

    Do the wires enter the box through a metallic fitting?

    You can do a continuity check with a cheap meter,

    (the 'ohms` scale), between the box and the white,

    (neutral), wire to confirm the existence of this ground.

    There are grounding clips that attach to the box to connect to the ground screw of the new outlets if your boxes are grounded.

    Good luck.How do you replace a 2 prong oulet with a 3 prong?Give the 10 to John.How do you replace a 2 prong oulet with a 3 prong?If the boxes are connected with EMT just run a green wire from box to box and connect to your receptacles ground screw. At the panel end there should be a ground lug that grounds your panel or a grounding strip,which if there is I dont know why they didnt run a ground to begin with. Your best bet ask a licensed electrician.How do you replace a 2 prong oulet with a 3 prong?easiest way is to add the new 3 prong(grounding screw ) outlets and run the ground wire on the green screw to a metal box or copper pipe anything that you know to be grounded

    How can i replace a compact flourescent bulb by warranty without holding on to the reciept for 5 years?

    I Called a few local stores and they say you have to have the receipt to replace it. I can't find a receipt after 2 weeks let alone 5 years for the whole warranty of a bulb.How can i replace a compact flourescent bulb by warranty without holding on to the reciept for 5 years?I tape the receipt to the bottom of the lamp or under the ceiling plate for light fixtures. I tape receipts to everything - like my ten year old mattress! If it can't be taped on or near the item, I have a file drawer for all the owner's manuals I get. I always check there next.How can i replace a compact flourescent bulb by warranty without holding on to the reciept for 5 years?My bulb had a 800 # on the base. I called it and they sent me replacements. No hassle.

    How do I replace the sub-flooring in my bathroom?

    There are linoleum tiles which are not the problem; I can get them up, but the sub-flooring (wood) around the toilet is old and rotting and I need to replace it. How do I lift the toilet off to repair the floor? Any other suggestions would be great!How do I replace the sub-flooring in my bathroom?This brings back nightmares. I don't know how many times I have done this!!!



    Shut off the water to the toilet. Flush and bail until it is empty. Unhook the fill tube at the valve. Remove the bolts at the base of the toilet. (You might have to pry the cover caps off with a screwdriver or chisel.) If the bolts will not come off, hacksaw them.



    Move the toilet out of the way. Sometimes putting a piece of cardboard in the tub makes a good place to place the toilet. Remove the floor with a saws all as far back as it is rotted. Sometimes you need to %26quot;scab%26quot; in support blocks for the new floor. This can be done with 2x4's and deck screws. When replacing the floor around the pipe, put the %26quot;split%26quot; part of the board parallel to the wall. This will give you a solid area around the front of the toilet where the traffic is.



    Cut your replacement board, and then lay it on the floor and mark the floor to identify the small places that will need to be trimmed.



    I am assuming that you have knowledge of carpentry, as there are 1,000 other details that I am leaving out. I am only putting in those that make a difference for the experienced handyman.How do I replace the sub-flooring in my bathroom?I used a shortcut when I had this problem, I removed the toilet and removed all the rotten wood I could then used a fiberglass repair kit with glass cloth and filled in the bad places. May not work if your floor is badly damaged but on mine it was the area right around the toilet flange.

    I did this two years ago and the flooring is still strong.How do I replace the sub-flooring in my bathroom?Please hire a pro.How do I replace the sub-flooring in my bathroom?I would not remove this subfloor.



    Get 1/4 hardwood plywood available at Home depot and steel plaster lath that is available from any Drywall supply house in 28 inch wide by 95 inch long galvanized( perforated metal is what this is) about $6 a piece is the cost.



    Sandwitch the metal lath between the hardwood plywood gluing the two together with a troweling of Polyurethane cement, use a ridge trowel about 1/8 high ridges. Then screw that to joists best you can with about #6 x 1 1/2 drywall screws.



    Of course you can lift off the toilet, just remove those two bolts and up it comes.



    You are asking for a major problem if you cut into this old subfloor. Every where you cut on the peremiter, you are going to form a non supported area that will squeal and be structurally inadequate even if you put in blocker blocks.



    This sandwitch of hardwood plywood and steel lath will have an equivalent strenth far above anything needed to support a new floor. That slight 7/32 inch rise at door ways will be unnoticable if you tile and use an edge strip. Remember, that 1/4 inch plywood is actually 7/32 thick not 1/4.How do I replace the sub-flooring in my bathroom?first disconnect the water supply line after you have shut off the valve..then flush the toilet.

    next there are two plastic caps under the bowl..pry them off and right there should be nuts to the toilet bolts..take them off and pull straight up on the toilet..

    if the floor is really rotten you may have to replace the toilet flange on the floor...not an easy jobHow do I replace the sub-flooring in my bathroom?At the bottom of the toilet, there are 2 or more bolts and nuts that hold the toilet tight. They are usually covered by caps and you have pry the covers off, loosen the bolts, and lift the toilet straight up. You also have to disconnect the water line.



    Tear out the subfloor and replace it, then get a new wax ring to seal the toilet, don't overtighten the nuts or you can crack the toilet. good luck. Had to do the same thing a few years ago.How do I replace the sub-flooring in my bathroom?remove all thats in the way of the floor and screw down new wood to the bath floor you willneed to make adjustments to accomadate toilet with the new height and doorway also thats the simplest less labor and does the job!How do I replace the sub-flooring in my bathroom?take up toilet



    Use a circular saw that you can adjust depth. Saw a square. Take up the square - need be use a chisel.



    In lay some plywood of correct depth - if need be shim with some wood shingles to make level. Now put on your new flooring



    Real lazy - get some plaster - scrape away the rotted leak area - now plaster it level.



    Smartest thing you can do is get a new Johnny ring - or go heir someone

    How often a landlord has to replace the carpet and repaint?

    I lived in Los Angeles county. I heard that after 5 years or 7 years, the landlord have to replace the carpet if he didn't replace after you have lived for 5 or 7 years, the landlord can't deduce money for the carpet or painting. So please let me know is it 5 years or 7 years?How often a landlord has to replace the carpet and repaint?Neither. There are no laws forcing paint and carpeting, ever. You do not even have to have them in the first place.How often a landlord has to replace the carpet and repaint?NOPE.

    LL NEVER has to replace carpeting and repaint.

    Go check out some slum apartments if you have any doubts.

    If LL wishes to get quality tenants, they periodically repaint and replace carpeting, but they are NOT required to do so by local or state law, but by the law of supply and demand.



    AND, if you damage or destroy LL's property, you are liable for repair or replacement, regardless of the age of it. It's wishful thinking or an urban myth.
  • rodents
  • cat
  • How do you replace the oil and gas in your mower?

    I bought a brand new lawn mower last summer, I used it and put it away when winter came. Now I want to use it again, and I've read that you should replace the oil and gas in it before using it again. But I don't know where or how to drain it. Thanks.How do you replace the oil and gas in your mower?If you tip the mower upside down like some of these highly informed individuals recommend you will have oil in the air filter and carburetor not to mention all over the ground. Unless you live in Arkanas don't do it that way.How do you replace the oil and gas in your mower?you should have removed the gas before storing it,

    if its a down shaft flip it over look on the bottom for a square nut, use a ratchet that size to remove it then put it down on the wheels %26amp; let it drain, put plug back in fill with oil

    [you should dump the old gas while you have it on its side,] it will evaporate,

    refill with fresh gas,

    should have read the manualHow do you replace the oil and gas in your mower?just start it and run it 'till it runs out of gas. OR, and here's the hard part, to empty the oil you will have to tip it over and drain the oil from the oil fill. they are kind of heavy so get a guy to help, if possible. point is, you can drain the gas while you drain the oil since you have to tip it over anyway.



    now this is important! when you drain the oil, tip the mower over where the oil will flow away from the gas tank.



    use an oil recycle bin to collect the old oil.



    this is kind of a mess for a rookie so you might want to put it in the shop for a spring tune up. WHATEVER you do, make certain you drain the old oil and put in fresh oil. IT IS CRUCIAL FOR A NEW MOWER!

    How do I replace my rotten porch posts?

    My house has a porch approx 7 feet from front to back and 11 feet wide. The base of the porch is concrete and it has 2 wooden posts supporting the porch roof. The wooden posts are starting to rot at the base so I want to replace them.



    I was thinking of using PT 6x6 posts which I will let dry out and then prime and paint before installation. Will this be ok?



    How should I attach the posts to the concrete and the roof to ensure they will be well secured?



    Will I be able to attach a wooden railing once I've attached the posts?How do I replace my rotten porch posts?First get an 8' treated 6%26quot; x 6%26quot; Post. Cut it in half and place each half under the porch roof beam at a diagonal on each corner of the porch. Take 3%26quot; screws and screw it into the porch beam back from the corners.

    Now something sturdy around the house, like concrete blocks,pc. 3/4%26quot; plywood and place these on the ground to rest your temporary braces on.

    Cut 2 4%26quot; x 4%26quot; posts to fit up under the end of your chunk of 6%26quot; x6%26quot;s at each corner. Wedge them up tight under the 6%26quot; x6%26quot; and fasten at top and bottom.

    Now you can remove your old posts.

    I would do a scaled drawing of your porch and see what size posts looks good. If it were mine I would probably laminate 4 layers of treated 2%26quot; x 6%26quot;s together to form your posts. Sometimes treated posts warp,twist,bow - but if you laminate 4 pcs. of 2%26quot; x 6%26quot; together it works better.

    You can purchase a metal base plate for these posts made by *Simpson. It anchors to concrete and wraps around post at the bottom.

    I would put up the posts and then wrap them with aluminum coil stock or cedar.

    Even if you use 6%26quot; x 6%26quot; treated posts - they will split,warp and not look very good, so you may want to wrap them or put on cedar.

    Remove temporary braces, you are doneHow do I replace my rotten porch posts?lolHow do I replace my rotten porch posts?You can buy buckets that screw to the concrete and the 4 sides fold up and you nail it to the sides of the post, cut a 1 x 6 PTand make a skirt . Strap the top also,and put a 1 x 4 crown at the top. Yes you can cut the handrail to fit back in. Nice little project, Good luck !How do I replace my rotten porch posts?Concrete anchors and a couple of 90'angles,then just use heavy gauge wood screws.You can paint before or after and add railings.Sounds like a cool idea.She'll look good when complete and sturdy.How do I replace my rotten porch posts?you can put the post in the ,you can pant it later. secured the post with concete screw on the bottom and screw top with wood screw. that will hold them in place. and you can put your railing back on .

    How much should it cost to replace a timing belt on a new style 99 Jetta GL 4 cylinder automatic?

    I just got an estimate from the dealer and they said $750 and it would take 4 days... they said they had to replace the water pump at the same time, too (even though there is nothing wrong with my water pump, I just need to get the timing belt replaced for maintenance purposes- it has not broken.) It seems like a very high estimate to me, but I called another dealer in the area and they said the same thing. Hopefully someone can give me some advice as to what it should cost. :) Thanks!How much should it cost to replace a timing belt on a new style 99 Jetta GL 4 cylinder automatic?The reason they want to replace the water pump is that they have to pull the water pump to replace the timing belt so they don't charge any extra for the labor just the parts (which they mark up) but it is recommended to get it done since it will likely need replacing eventually, cheap insurance. Timing belts replacement is something that annoys me as well and when I buy a car I always try to factor that cost into my buying decision, especially on used cars. If you call three or four different auto mechanics and the price is roughly the same you'll know that's about right. Most mechanics use a guide that tells them how long a specific job will take and bill accordingly.



    If you are feeling REALLY adventerous you could find out if your valve train is interference or non-interferance. If the timing belt breaks on an interference engine, the pistons will hit the valves and cause serious damage, as in the engine is toast. On a non-interferance engine, it will usually just stop running at which time you can pay a towing bill and have the belt replaced. A friend on mine is on the original belt in his 91 Honda and now has 175,000 miles on it. He bought a used engine for about $500.00 and plans to replace it himself when the belt gives out.How much should it cost to replace a timing belt on a new style 99 Jetta GL 4 cylinder automatic?Dealer 600-700How much should it cost to replace a timing belt on a new style 99 Jetta GL 4 cylinder automatic?Your car has an %26quot;interference engine%26quot; that will suffer expensive damage if the timing belt breaks. So you have no choice other than to have the belt and water pump replaced. Next time, think about getting a car that has a timing chain rather than a timing belt. Timing chains last the life of the car with regular engine oil changes.How much should it cost to replace a timing belt on a new style 99 Jetta GL 4 cylinder automatic?That's about average rate an the timing belt runs the watter pump u do not have to replace it but i have seen it many times where a belt was changed ab the pump went bad a month later now u going to pay another 600+ buck s so the Chance of a 1200+ repair or a 600+ repair would be your choice mine would be do both at one time Some timing belts are a high labor job

    There were a few early models you had to remove the engine to replace the t belt

    How do I replace a garbage disposal with regular piping?

    I have a garbage disposal that don't work. I think the motor is burnt out. I was wondering if anyone knew how hard it was to just take the disposal out and replace it with regular pipe. Is this something that I could do myself or would I have to hire a plumber. Any advice would be a big help. Thanks in advance to all who will take time to pass their advice on.How do I replace a garbage disposal with regular piping?Garbage disposals are detrimental to the sewer system, garbage belongs in the garbage can, many local authorities have banned their replacement, if you want to keep taxes down, it costs to treat everything that goes into the drain. First, SHUT OFF THE ELECTRIC, if you can't, forget about doing the job. Open the box where the wire enters the disposal, disconnect the wires and place wire nuts and electrical tape over them. Cut the pipe that leads to the wall, just after the u-shaped bend. Support the disposal, Hit the ring at the top of the disposal, counterclockwise, or put a screwdriver into one of the loops and twist. Take the back end of the pipe you cut off the u-bend[trap], to the home store and ask for a Fernco fitting to attach the pipe out of the wall to the new trap, purchase the trap, preferably plastic; the tailpiece, and the basket strainer to go into the sink opening, use silicone caulk to install the strainer, they will tell you to use plumbers putty, don't. Good Luck!How do I replace a garbage disposal with regular piping?try turning the disposal with the wrench that came with it, push the little red reset button at the bottom, check the breaker, will it run now ? to remove it take disposal loose theres a ring that holds it on turn it counter clock wise, unplug disposal, then you can hook up regular pipes to the sink drain,How do I replace a garbage disposal with regular piping?Just remove the disposal ,and any wiring, and connect remaining pipes with a short length of pipe. (be sure to dope up the pipe good so it don't leak) a pretty simple operation really.How do I replace a garbage disposal with regular piping?your local hardware store will be more than glad to help and do it right.How do I replace a garbage disposal with regular piping?Look on the bottom on the disposal for a reset button. If it still dont work check to see if it has power .

    How do I replace/install an interior door and frame?

    I need to replace the interior doors of my home, they are very dated. I see at lowe's or home depot I can purchase them, but I have never installed one before.How do I replace/install an interior door and frame?If you want to save the existing molding, start by gently scoring the frame along the wall with a razor knife. Get a small flat bar and gently pry the molding until you can see where the finish nails are. Use the smallest nail set or punch available and drive the nails through the molding and remove.

    Remove the door from the frame as well as any shims. Pry the frame off the studs and header or saws-all them off.

    Now the important stuff. Carefully cut the bottom of the jambs for height. The top of the jamb should be within 1/4 inch of the header. Remove the door from the new unit and install the jamb using finish nails and shims to ENSURE it is level, square and true. Take your time as that is the most important part. Hang the new door and test it. If things look good, replace the molding, set the nails, fill and paint/stain.

    Good luck
  • programming
  • got a call saying
  • How much does it cost to replace the battery of a car starter?..?

    I have a two car starters.



    I lost one and then I used the spare one.

    My friend found it as it was hiding out in her car..

    but it doesn't work. The battery died. How much does it cost to replace the battery of the car starter?..



    It belongs to a '95 Checy Blazer..if that helps.How much does it cost to replace the battery of a car starter?..?batteries all different prices depending on how long its gauranteed a 12 month battery would be abot 22 dollars.. and a five year battery would be about 50 dollars.. go to the store give your make and model and they will suggest a replacement. ok.How much does it cost to replace the battery of a car starter?..?you mean remote start then say that people dont know how to say things that they own i understand if its a difficult part of the car you dont know but remote start aint that hard its probably a $10 or less fixHow much does it cost to replace the battery of a car starter?..?are you talking about the remote control?

    How do I choose a sump pump to replace the existing one?

    How do I choose a sump pump what do I need to take into consideration? If possible I would like one with multiple speeds which matches the amount of water the one which is there is not emptying the water table it is quite highabout an inch below the bottom of hole, it is about 40 years old we think as it looks like the system was installed with the house it is either that or they put a whole new concrete floor in when they did it over.How do I choose a sump pump to replace the existing one?Many years ago I had to replace a sump pump in the basement where I lived at that time.

    I had to consider the following when getting one.

    1. voltage available

    2. Height of water to be removed at the very worst- I increased this so it will not come on as often and will pump more out when it does.

    3. How long to empty water before it refills again- I wanted this to be less in case of constant fillup during rainstorms.

    4. Distance to be pumped - how far to the outlet- you want it to be able to pump the above at a distance greater than what you require - I looked for one for 6 feet since I only needed 3 feet to sewage outlet.



    For me, the pump that was there would clear out the %26quot;Hole%26quot; in about 4 minutes - it was about 4 gallons of liquid when full.

    I replaced it with a pump that can pump out that amount in about 1 minute - just because if a heavy rain comes the pump can't keep up with the rainwater before.



    I made sure the height could be adjusted so I can get higher to allow more water to fill in it, before activated - and empty it out in less than 1/2 the old time.

    So I would say you want to increase height if you can - no matter what that height is you want it to pump faster than it did, about 1/4 the old time with the new height.

    I only used a single speed - I felt that is all that was needed - to pump or not to pump.

    Make sure it is braced pretty well too - I had an issue with this - even with the old one. Oh and don't drain to the bottom totally or the pump will suck up dirt if its not finished in there.

    Remember the longer a pump runs the shorter its life will be - this is why I did what I did to not have the pump run long periods, plus if I got a really bad storm I know this pump will handle most of that much easier. Not to mention - this pump will last many years no problem. It really is cheaper to by more than you need today - than it is to buy smaller pumps every 10 or 15 years. This pump really could last 60 years in there no problem, that is about four smaller pumps. If the difference today is $30.00 That smaller pump will cost more to replace several times that the purchase of a larger pump.



    So I would strongly suggest %26quot; Go Big (Liquid Volume)%26quot;How do I choose a sump pump to replace the existing one?it depends how much water gets in your basement and how often. I don't think they make them with more than one speed. Its measured in how many gallons it pumps out in a hour, they sit in the sump pit and pump as water passes them so they dont even need more than one speed. Just make sure u get one big enough to keep up with the amount of water coming in.. which doesnt take alot..go to like a home depot or something and tel them what u want, and how much water u get...they will point u to the right one.How do I choose a sump pump to replace the existing one?I don't know of one with multiple speeds. You can, of course get different size ones but, your going to pay the price. Make sure you need the one your going to buy. They Can be pretty expensive.



    Get one of the newer ones that are self contained and small. they don't look like pumps anymore. Go to a farmers supply place, Home Depot, Lowes, etc.How do I choose a sump pump to replace the existing one?Zoeller is the brand that i had put in recently- mine went out- some brand from menards-the house is only 3 years old so go figure-but the one they replaced it with is cast iron.



    www.Zoeller.com

    How much would it cost to replace the water pump on a 3.5L 300M?

    The water pump in my 2000 chrysler 300m is starting to fail - how much should I expect it to be to replace/repair.How much would it cost to replace the water pump on a 3.5L 300M?For a used part, request a quote from somewhere like Greenleaf Auto Recyclers or car-part.com ... for a new part, call your local Chrysler/GM dealer, ask for the parts department, and ask for the cost of the part. While you're at it, ask them for the repair time to replace the water pump. If you can get that, multiply the repair time in hours by about $100 (what places charge around here for mechanical work) and add the cost of the part.

    How much would it cost to replace my front bumper?

    ok so today my 1999 honda civic lx slid on ice into a mailbox. the front bumper has a 1 foot crack on the driver side and there are some scratches... how much would it cost to replace the bumper?How much would it cost to replace my front bumper?The cost for an aftermarket bumper should be less than $100. Then you have to pay someone to remove, repaint, and replace the bumper cover. This could vary from $200 or so from a small shop to + $700 from a large body shop.How much would it cost to replace my front bumper?Your looking at more than $100, but less than $200.

    Go to http://www.amazon.com , then search 1999 Honda Civic bumper, there is a pretty good selection there, but you also may not find one you like, so good luck.

    How to replace toilet flange on cast iron soil pipe?

    Is there anyway to replace the flange, and if so how would you go about it?How to replace toilet flange on cast iron soil pipe?I'm assuming you're changing the flange because it is broken. I'm also going to assume you have poured lead joints connecting it.



    What I would do is this, there are a few ways to cut cast iron pipe, I hope you have a sawzall, if so you need to get a diamond grit blade, prefferably an 8%26quot; one, made for cutting cast iron. the pipe that rises up to the toilet flange, find a spot on it that you can access with a sawzall to cut it, it's a slow process but it will get through eventually. cut the pipe off about a foot or so below the old flange.



    But make sure that you make a cut at least 6%26quot; away from any hubs. If the pipe is 4%26quot;, get a 4%26quot; x 3%26quot; Fernco (rubber) adaptor. These are used for joining 2 dissimilar types of pipe together. After this you'll need a piece of 3%26quot; pipe and a toilet flange. (If the floor is bad around the toilet this is also a good time to fix that.)



    Put the Fernco adaptor on the cast iron and tighten it on with the hose clamp that comes with it. Put a piece of 3%26quot; pipe into the other end of the Fernco, long enough to go through the floor. Don't tighten it into the clamp yet, the top of this pipe should be flush with the top of the floor, if it's not cut it so it is.



    Now, glue this pipe into the new toilet flange. (If you have a basement, this should be alot easier.) Put the pipe through the hole in the floor into the fernco. Measure from the back wall to the center of the toilet flange, line up the bolt slots for the flange with this measurement.



    Screw the flange to the floor, use large head phillips screws. It is important to do this. Don't forget to tighten the 3%26quot; pipe into the fernco. Put the toilet back on, I assume you already know how to do this. Check for leaks, and that's it.



    Good LuckHow to replace toilet flange on cast iron soil pipe?Couple of acceptable ways to just replace the flange.

    1. Using a small chisel, cut all the old lead out of the old flange around the pipe. This should allow you to remove the existing flange. Purchase a new flange, caulk with oakum and pour lead and tamp with caulking iron to secure and seal. Secure new flange to floor.



    2. Purchase new flange replacement that actually fits over existing cast pipe and seals securely using bolts that compress seal. Securely anchor to floor. This may require removing a little flooring material around the pipe to allow flange to fit.



    2a. They also make a PVC replacement that fits inside a 4%26quot; cast iron and tightens the seal using bolts. However, you may still need to cut the cast iron pipe to get the replacement flange to fit tight against the floor. The cast iron pipe can be trimmed easily with a small angle grinder. Just watch the sparks.How to replace toilet flange on cast iron soil pipe?Go to your local plumbing supply store and tell them the problem. They make a PVC replacement for cast iron, the problem is having room to put it on. If it is a concrete floor, you are looking at busting up some concrete. If it is a conventional floor you will have a much easier job. Good luck!How to replace toilet flange on cast iron soil pipe?If you have a busted flange that isn't too badly broken out, they have repair parts for them. It is basically a curved piece of metal that slips beneath the flange and spans the broken area so you can clamp the toilet down. I had a flange break out and I got the repair part at Home Depot for just a few dollars... There ain't no easy way to change one!!! ....Good Luck...
  • getting an error report
  • blue hair
  • How much would it cost to replace an Acura ignition and steering column?

    I have a 1992 Acura Integra GS-R that was stolen and is now back in my possession however the ignition has been ripped out and i think there is damage to the steering column. How much would it cost to replace these part? (I didn't have theft insurance coverage... sigh ... i know).How much would it cost to replace an Acura ignition and steering column?I helped a friend replace this stuff on her 1993 Honda recently. The ignition stuff alone was about $300. You can probably get the steering column stuff from a junk yard for less than $50. Good luck. It is NOT easy to replace this stuff doing it yourself. If you pay somebody to fix it, you may as well double the cost.

    Anybody know how much money is to replace a bad lifter valve and The timing chain tensioners on a 99 Ford Expl?

    Anybody know how much money is to replace a bad lifter valve and The timing chain tensioners on a 99 Ford Explorer 4.0 engine on a regular shop? What happen if i dont replace it?Anybody know how much money is to replace a bad lifter valve and The timing chain tensioners on a 99 Ford Expl?I assume this is the SOHC 4.0L.



    You lose the engine if you don't replace them as the engine will jump time. Since this engine is an interference engine, that means 12 bent up valves at least.



    You must pull the engine to get to the passenger side assembly as it is in the rear of the engine!Anybody know how much money is to replace a bad lifter valve and The timing chain tensioners on a 99 Ford Expl?About 1,800 dollars and you will at some point ruin the motor if it's not fixed.Might cost more once they get into the job.

    How do i now what kind of replace a top to buy for my 2000 wrangler or the style to buy?

    i am not sure if i need to buy the manafactured or the othertype of top for my jeep how do i tell the difference? i have bought the replace a top in the past and they did not fit. how do i now what style is right for my jeep?How do i now what kind of replace a top to buy for my 2000 wrangler or the style to buy?Go to 4wheelparts.com where you'll find the complete line of Bestop soft-tops. I bought the sailcloth top and have been very happy with it. A replace a top uses your original hardware, or you can get a super top which comes with new (improved) bows.How do i now what kind of replace a top to buy for my 2000 wrangler or the style to buy?www.Bestop.com



    They have the best selection. I have a 99 Wrangler they are the only aftermarket top I would go with.



    Look at the Sunrider soft top.How do i now what kind of replace a top to buy for my 2000 wrangler or the style to buy?go to the dialer and ask them what kind of top you need they will tell youHow do i now what kind of replace a top to buy for my 2000 wrangler or the style to buy?QUADRATEC.COM Best damn Jeep aftermarket place there is

    How much will it be to replace an exhaust on Fiat Punto?

    My exhaust on my Fiat Punto 03 reg all of a sudden sounded like a tank. Does anyone know how much it will be to fix? ThanksHow much will it be to replace an exhaust on Fiat Punto?Depends if you want to replace the unit yourself but unless you have either know how and tools /equipment leave it to the experts.



    I prefer National of the larger quick fit chains but they all tend to want to replace the whole exhaust rather that just the part that is gone and normally if they replace the lot they give a 5 year guarantee otherwise just 1 year on a single part.



    If you were considering doing yourself you would fist of all need to find out what part or parts of the exhaust have holed and to do that you could just run the engine get someone to place a rag over the end of the exhaust pipe just for a few seconds at a time while the other person looks for where it is holed.



    If it is just the back box and the rest of the exhaust is fine you perhaps go to a motor factor and buy a replacement part .



    As I say if you are not familiar with the item and don't have the tools you must go to a garage : get three quoat for three garages and then chose who you trust the most.



    I suspect it may cost around 100 to 120 pounds for a full exhaust.



    Good luck



    PretenderHow much will it be to replace an exhaust on Fiat Punto?probably more than it would cost to replace the punto that is stuck to your broken exhaust...How much will it be to replace an exhaust on Fiat Punto?just depends where u have it fitted,say around 70 quid

    How much will it cost me to replace my 2000 VW Passat Heater Core?

    How much will it cost me to replace my 2000 VW Passat Heater Core?Parts and Labor? Not sure how much this might run. ThanksHow much will it cost me to replace my 2000 VW Passat Heater Core?It depends where you take it to and if you have an air conditioner. To replace it the mechanic has to take apart the dash. I had a quote from a dealer for my Ford Taurus 93 and it would have been $600, for some reason if you have an air conditioner rather than just a vent system it takes longer work. A friend of my husband did it for $150 and a couple cases of beer. The part itself is less that $100.
  • curly hair
  • myspace cursors
  • How do I replace/install an interior door and frame?

    I need to replace the interior doors of my home, they are very dated. I see at lowe's or home depot I can purchase them, but I have never installed one before.How do I replace/install an interior door and frame?If you want to save the existing molding, start by gently scoring the frame along the wall with a razor knife. Get a small flat bar and gently pry the molding until you can see where the finish nails are. Use the smallest nail set or punch available and drive the nails through the molding and remove.

    Remove the door from the frame as well as any shims. Pry the frame off the studs and header or saws-all them off.

    Now the important stuff. Carefully cut the bottom of the jambs for height. The top of the jamb should be within 1/4 inch of the header. Remove the door from the new unit and install the jamb using finish nails and shims to ENSURE it is level, square and true. Take your time as that is the most important part. Hang the new door and test it. If things look good, replace the molding, set the nails, fill and paint/stain.

    Good luck

    How do I replace my 1998 Lincoln continentals driver side mirror?

    The drivers side mirror is delaminated and has turned completely black. How do I get into the housing to replace the mirror?How do I replace my 1998 Lincoln continentals driver side mirror?you need to remove the door panel. but be careful the pins like to break after they have been on for a while.How do I replace my 1998 Lincoln continentals driver side mirror?Go to an auto parts store and get a repair manual for your vehicle.How do I replace my 1998 Lincoln continentals driver side mirror?you have to take the door panel offHow do I replace my 1998 Lincoln continentals driver side mirror?If it's like the one on my 98 MARK VIII ,you simply snap it off of the ball-and socket mounts on the motor. If you buy a new one ,the fittng should become obvious, and mine only cost 300 bucks,with a 20% discount!

    How do I replace a cigarette lighter socket on a 1998 Mercury Sable?

    I need to replace the bad/defective light socket and do not know how to excess it.How do I replace a cigarette lighter socket on a 1998 Mercury Sable?first of all remove fuse to kill power.

    Hold the body and stare to turn the inner section. Once the sections seporate you can replace it.

    Wire connection on rear and threads in same.

    How much does it cost to replace a steering column in a '93 Lincoln?

    Someone stole our car a week and a day ago, we got it back this morning, they hadn't done anything to it except screw up the steering column. they sawed through some of the metal parts in there, so now we have to replace the entire thing. Does anyone know how much it costs to replace all of it?

    it's got cruise control setting and that sort of thing on the steering wheel. We don't know how much money we're gonna be looking at spending so we're not sure what to do just yet. and we can't get anyone to give us a straight answer when we call.

    Oh, and we live in the houston, texas area if that makes a difference. sometimes stuff is cheaper from one city/state to the next, so if that helps at all. Any info we could get would be great.

    We can't get salvage yards to tell us how much it'll cost cuz they said they don't do inventory they're 'u-pick-u-pull' places, so they don't know. we're trying to weigh our options on what'd be the cheapest thing to do.How much does it cost to replace a steering column in a '93 Lincoln?call a repair shop

    How do you replace an ignition cylinder in a 1987 Cadillac Eldorado?

    I need some instructions on how to replace an ignition cylinder lock on a 1987 Cadillac Eldorado Biarritz. Thanks for your help in advance.How do you replace an ignition cylinder in a 1987 Cadillac Eldorado?I will refer you to a website try alldatadiy dot com or mitchell1.com. They have step by step instructions with pictures, good luck.
  • extension to sqltableprovider
  • ram interrogate
  • How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?

    I have the new mirror, but I want to install it myself, does anybody know how to do this, or of a repair guide that would explain how to replace the mirror?How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?Just get it done in the shop.How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?take the plastic cover off just inside your door behind your mirror it should just clip off behind the cover is a few screws remove them undo the plug for the electric mirror and it should come out without to much troubleHow can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?With the proper tools, remove the door panel trim. Peel back the weather shield. With the window rolled up find and remove the two bolts that hold the mirror.

    Allow it to hang by the wires and go under the dash and disconnect the plug from the body wiring and remove the retainers holding the harness. Now slip the cable assembly out through the door. Reverse this procedure to install the new mirror.

    Hope you had it painted the proper color.

    How do you replace a shower head pipe?

    The showerhead pipe is copper and all the pipe threads broke off at showerhead. Can I add threads to the remaining pipe with a tool or something? If not, is the pipe sticking out of the wall easy to replace?How do you replace a shower head pipe?Yeah the shower head arm should unscrew from its socket. The threads are sealed on the other end though so you will need to use a set of Channel Lock pliers.

    When installing the replacement use thread sealant - teflon tape will do. be sure to protect the finish of the new arm with a rag or some thin cardboard so you don't mar the finish.How do you replace a shower head pipe?I don't recommend adding threads.

    Try to remove the existing piece of pipe with a pair of pliers. Next buy a new piece and reinstall it. I recommend wrapping the threads with teflon tape (about two or three wraps).How do you replace a shower head pipe?all u need to do is take a rubber handle pair of pliers and stick one end in the shower neck (the part that has broken off) then turn it counter clock wise to unscrew it. then put teflon tape on the end furthest away from the curve and insert it into the wall and screw in clock wise. add the shower head and test for leaks.

    How do you replace a thermocouple on a hot water heater?

    My hot water keeps going out like once a week, i was told to replace the thermocouple, any suggestions?How do you replace a thermocouple on a hot water heater?turn Gas Off There Should Be 3 Fitting's on Bottom Of Control 1 is for main Burner 2nd is for pilot and 3rd is the thermocouple if you lossen those 3 whole Burner assembly will Come Out after you get it out Remove copper colored Thermocople and Replace It Then Re install Burner And Tighten 3 Fittings Turn Gas On And Soap Test burner and pilot Connection if Okay Then Re Lite Pilot.How do you replace a thermocouple on a hot water heater?i dont know, but i do know this, it is called a Water Heater, not a Hot Water Heater. If it is hot water why would you heat it?How do you replace a thermocouple on a hot water heater?http://homerepair.about.com/od/plumbingr

    and the clickable links in red might help, good luck



    or this one

    http://www.diynetwork.com/diy/shows_detpHow do you replace a thermocouple on a hot water heater?Very simple but, if your not mechanical minded and you don't have the tools it's best to have someone come in. Ask a friend if they've ever done it, etc, it is easy.How do you replace a thermocouple on a hot water heater?Bob R said it pretty good although you may be able to do it without removing the whole burner assembly.......some heaters are different though.....I always leave the burner assembly in but if you are unsure of what you are doing then you might want to take it out.....if it's a whirlpool water heater then the thermocouple threads are left-handed!

    How do I replace a sliding glass door with a window?

    I need to replace a glass door with a wall and frame a window. Are there any how to plans out there to use?How do I replace a sliding glass door with a window?I'm assuming that this is for a patio door. When was your house built? That will determine if you need a size for new construction or retro-fit. If you want to replace the doors AND the frame, you can order the unit prehung (go to Lowe's or Home Depot. You can get a quality product for a good price) and get a contractor to do the actual installation. The contractor would then determine the RO (rough opening). For instance, if you have two 3' x 6'8%26quot; panels (6' X 6'8%26quot; total, which is standard size), your rough opening would probably need to be about 741/2%26quot; width x 81 1/2%26quot; height. That would leave room for the contractor to shim the doors before the brick is put back in place.



    I hope that this helps.How do I replace a sliding glass door with a window?First you need to decide the size %26amp; type of window you plan to install prior to building a frame and closing in the wall. Do you want a double hung, casement, glider type window, etc. Once you determine that, then what size. Go to your lumber yard or home center with that window size to get the size of the rough opening you will need. Fortunately since you already have a door in place then the old opening already has a header installed and framing will be easier. Good luckHow do I replace a sliding glass door with a window?First things first, decide what size window you want to put in placement of the door, Being in construction as a rough framer for the past 15 years i can tell you this, if you want to put in say a 3foot by 4 foot window the first number is the width and the second number is the height, once you have decided what size you want then you have to decide if you want to center the window in the opening you all ready have or hold it off to one side or the other, once you have decided where you are going to locate it then comes the time to frame it in, now back to the number that i had mentioned before, if you bought a 3 x 4 window then you would frame the opening at 3 foot wide by 4 feet tall i know it sounds weird but the windows actually come out smaller than you think, it allows a 1/2 inch on either side to allow for shimming and leveling the window then when you put up drywall it can go back to meet the window, there is some books at home depot and Lowe's that can show you a better detail of how it all goes together, now what i have described above ,is what we deal with everyday is for standard vinyl windows, i hope this will help you and good luck with your project.

    How do you replace the steering wheel on an 84 Toyota pickup?

    So I have an 84 Toyota pickup and I went to take the steering wheel off to replace it the other day and after I took the front horn panel off there was, what seemed to be a lock or something. It looked brass and rectangular and it seemed to be holding the wheel on even after I removed the center nut. Anyone have any tips?How do you replace the steering wheel on an 84 Toyota pickup?Generally the steering wheel cannot withstand a very strong pull from you. You might want to rock the wheel a little while pulling one side then the other . Steering wheel puller are made for just that job. Some time i leave the nut screwed on a couple of threads so I don't smash the wheel into my face. Your old truck is old enough that it might need more than a steering wheel.How do you replace the steering wheel on an 84 Toyota pickup?1984? Take the vehicle to your dump, and then go and get something much newer. You sound American, surely you could buy something much newer and better for minimal cash?How do you replace the steering wheel on an 84 Toyota pickup?Are u kidding me? That piece of sh!t is not even worth buying gas for!! Take it to the dump and get another car.
  • connecting database
  • good middle name
  • How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?

    I have the new mirror, but I want to install it myself, does anybody know how to do this, or of a repair guide that would explain how to replace the mirror?How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?Just get it done in the shop.How can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?take the plastic cover off just inside your door behind your mirror it should just clip off behind the cover is a few screws remove them undo the plug for the electric mirror and it should come out without to much troubleHow can I replace the passenger side mirror on a 2002 Ford Focus with power mirrors?With the proper tools, remove the door panel trim. Peel back the weather shield. With the window rolled up find and remove the two bolts that hold the mirror.

    Allow it to hang by the wires and go under the dash and disconnect the plug from the body wiring and remove the retainers holding the harness. Now slip the cable assembly out through the door. Reverse this procedure to install the new mirror.

    Hope you had it painted the proper color.

    Friday, September 23, 2011

    How do you replace a shower head pipe?

    The showerhead pipe is copper and all the pipe threads broke off at showerhead. Can I add threads to the remaining pipe with a tool or something? If not, is the pipe sticking out of the wall easy to replace?How do you replace a shower head pipe?Yeah the shower head arm should unscrew from its socket. The threads are sealed on the other end though so you will need to use a set of Channel Lock pliers.

    When installing the replacement use thread sealant - teflon tape will do. be sure to protect the finish of the new arm with a rag or some thin cardboard so you don't mar the finish.How do you replace a shower head pipe?I don't recommend adding threads.

    Try to remove the existing piece of pipe with a pair of pliers. Next buy a new piece and reinstall it. I recommend wrapping the threads with teflon tape (about two or three wraps).How do you replace a shower head pipe?all u need to do is take a rubber handle pair of pliers and stick one end in the shower neck (the part that has broken off) then turn it counter clock wise to unscrew it. then put teflon tape on the end furthest away from the curve and insert it into the wall and screw in clock wise. add the shower head and test for leaks.

    How do you replace a thermocouple on a hot water heater?

    My hot water keeps going out like once a week, i was told to replace the thermocouple, any suggestions?How do you replace a thermocouple on a hot water heater?turn Gas Off There Should Be 3 Fitting's on Bottom Of Control 1 is for main Burner 2nd is for pilot and 3rd is the thermocouple if you lossen those 3 whole Burner assembly will Come Out after you get it out Remove copper colored Thermocople and Replace It Then Re install Burner And Tighten 3 Fittings Turn Gas On And Soap Test burner and pilot Connection if Okay Then Re Lite Pilot.How do you replace a thermocouple on a hot water heater?i dont know, but i do know this, it is called a Water Heater, not a Hot Water Heater. If it is hot water why would you heat it?How do you replace a thermocouple on a hot water heater?http://homerepair.about.com/od/plumbingr

    and the clickable links in red might help, good luck



    or this one

    http://www.diynetwork.com/diy/shows_detpHow do you replace a thermocouple on a hot water heater?Very simple but, if your not mechanical minded and you don't have the tools it's best to have someone come in. Ask a friend if they've ever done it, etc, it is easy.How do you replace a thermocouple on a hot water heater?Bob R said it pretty good although you may be able to do it without removing the whole burner assembly.......some heaters are different though.....I always leave the burner assembly in but if you are unsure of what you are doing then you might want to take it out.....if it's a whirlpool water heater then the thermocouple threads are left-handed!

    How do I replace a sliding glass door with a window?

    I need to replace a glass door with a wall and frame a window. Are there any how to plans out there to use?How do I replace a sliding glass door with a window?I'm assuming that this is for a patio door. When was your house built? That will determine if you need a size for new construction or retro-fit. If you want to replace the doors AND the frame, you can order the unit prehung (go to Lowe's or Home Depot. You can get a quality product for a good price) and get a contractor to do the actual installation. The contractor would then determine the RO (rough opening). For instance, if you have two 3' x 6'8%26quot; panels (6' X 6'8%26quot; total, which is standard size), your rough opening would probably need to be about 741/2%26quot; width x 81 1/2%26quot; height. That would leave room for the contractor to shim the doors before the brick is put back in place.



    I hope that this helps.How do I replace a sliding glass door with a window?First you need to decide the size %26amp; type of window you plan to install prior to building a frame and closing in the wall. Do you want a double hung, casement, glider type window, etc. Once you determine that, then what size. Go to your lumber yard or home center with that window size to get the size of the rough opening you will need. Fortunately since you already have a door in place then the old opening already has a header installed and framing will be easier. Good luckHow do I replace a sliding glass door with a window?First things first, decide what size window you want to put in placement of the door, Being in construction as a rough framer for the past 15 years i can tell you this, if you want to put in say a 3foot by 4 foot window the first number is the width and the second number is the height, once you have decided what size you want then you have to decide if you want to center the window in the opening you all ready have or hold it off to one side or the other, once you have decided where you are going to locate it then comes the time to frame it in, now back to the number that i had mentioned before, if you bought a 3 x 4 window then you would frame the opening at 3 foot wide by 4 feet tall i know it sounds weird but the windows actually come out smaller than you think, it allows a 1/2 inch on either side to allow for shimming and leveling the window then when you put up drywall it can go back to meet the window, there is some books at home depot and Lowe's that can show you a better detail of how it all goes together, now what i have described above ,is what we deal with everyday is for standard vinyl windows, i hope this will help you and good luck with your project.

    How do you replace the steering wheel on an 84 Toyota pickup?

    So I have an 84 Toyota pickup and I went to take the steering wheel off to replace it the other day and after I took the front horn panel off there was, what seemed to be a lock or something. It looked brass and rectangular and it seemed to be holding the wheel on even after I removed the center nut. Anyone have any tips?How do you replace the steering wheel on an 84 Toyota pickup?Generally the steering wheel cannot withstand a very strong pull from you. You might want to rock the wheel a little while pulling one side then the other . Steering wheel puller are made for just that job. Some time i leave the nut screwed on a couple of threads so I don't smash the wheel into my face. Your old truck is old enough that it might need more than a steering wheel.How do you replace the steering wheel on an 84 Toyota pickup?1984? Take the vehicle to your dump, and then go and get something much newer. You sound American, surely you could buy something much newer and better for minimal cash?How do you replace the steering wheel on an 84 Toyota pickup?Are u kidding me? That piece of sh!t is not even worth buying gas for!! Take it to the dump and get another car.
  • hair braiding
  • medium length hair
  • How do you replace a window with a bay window style?

    I'm tryng to replace my old window attached to my kitchen sink with 5'x3' baywindow. I need to know the basic steps on how to layout the framing, what's the process of isntallation.How do you replace a window with a bay window style?After the removal of the unit you need to reframe the rough opening if the unit is a different size. If not you should check the condition of the framing members that are in the wall already. If you do resize the opening I would reccomend a double jack stud as well as a double window will. If you are going to replace your header then I would use LVL material, same size, greater strength. Next you need to apply what we on Long Island call %26quot;visqueen%26quot; but the rest of the world calls poly. This goes on the sill first and then the jack studs. It creates a water barrier. Next install the new window using the cable support system that should be included with the unit. Use silicone at all nail flanges to ensure it is watertight. i would also recommend using a Tyvek of Vycor window flashing system around the unit...it is a little pricy but well worth it. Reside around the unit and you are done outside. Stuff insulation in all new openings, install the head and seat boards, patch all the sheetrock and install the casing. GOOD LUCK

    How do I replace spark plugs on a transverse v6?

    I bought mine new and now my car, 03 Sable, has 110000 on it. I want to replace the spark plugs now. I can get to the front with no problem, of course. How do I get to the back side?

    Also any good books to get that would explain how to do general maintance on newer cars? Seems like flushing the radiator on new cars is so much different than cars from the 60's.How do I replace spark plugs on a transverse v6?For a manual, ya can't beat ' Haynes '. The rear plugs aren't to bad to change on a Sable 3.0 'ohv ' engine, but I haven't done'em on their overhead cam 3.0. Also, on the cooling system flush, Don't use those chemical flush treatments.Just pop off the bottom hose, like ya did on the old cars,%26amp; rinse'er out afew times. Good Luck =^ )How do I replace spark plugs on a transverse v6?unfortunately fords are a ***** to dig into. sometimes you can go underneath and get em. a trick i use if i have to is to un bolt the torquer motormount have someone get in the car and put it in gear and slowly gently accellerate untill theengine rolls a bit opening the gap between the engine and firewall.carefully place a wooden block in a place that it will be secure.without a small protrusion pushing into the wood(splitting it and causing collapse of the gap)once in place add spacers where applicable for added safety). dont try this if you feel uncomfortable with doing so.when i use this method i usually use a foot long 4x4 in good shape with no knots.when working on any ford have patience and remain levelheaded you will probably notice that it's been engineered by a blind idiot.

    How much to replace a broken hot surface ignitor and a flame sensor?

    My Bryant furnace did not start on Friday night. A technician came in to replace the ignitor and flame sensor and he charged me $165 for the service, $97 for the sensor, and $293 for the ignitor, total $550. I believe I got ripped off. Any thought?How much to replace a broken hot surface ignitor and a flame sensor?I am an HVAC tech, if I went on this call this is what I would charge on a FRIDAY night (after 5pm). This is from my price book, I work for a major company in my city.



    Flame sensor- $35.00

    Ignitor- $75.00

    Labor- $250.43 (1 1/2 hours @ time and a half, one hour for the service and a half hour travel time)



    Total- $360.43



    My guess, the flame sensor just needed a cleaning with some steel wool. (that does the trick 9 times out of 10)





    So yes you did get ripped off, more so on the ignitor than anything else. I would call the service manager at the company and ask why the ignitor was so grossly overpriced!How much to replace a broken hot surface ignitor and a flame sensor?SENSOR for GOODMAN 17.00 IGNITER for GOODMAN 37.00 !How much to replace a broken hot surface ignitor and a flame sensor?1 hour labor $80

    flame sensor and ignitor $60How much to replace a broken hot surface ignitor and a flame sensor?yeah, you got ripped off. That is what most those type of bisnesses do.

    and you had to pay a little more for fiday night service.

    you can look online to see what you could have bought the parts for and then you will know..

    google %26quot; appliance parts%26quot; and follow the directions ,you will need the model # etc.How much to replace a broken hot surface ignitor and a flame sensor?Yes you did. I just replaced the ignitor on my Goodman , paid $45 with shipping. The flame sensor would have been about $20 more. You probably did not need the sensor.

    How do I replace LEDs for Coralife Lamps and where do I get the bulbs?

    I have had 36%26quot; Coralife lamps, with daylight, monnlight, and LEDs, for about 6 months on my 75 gallon corner tank The LED bulbs quit. I can't figure out how to remove/replace them.How do I replace LEDs for Coralife Lamps and where do I get the bulbs?pet co petsmart rate as best you got to pull it towards u

    How do vegans replace their dairy vitamins?

    I'm a vegetarian and planning to go vegan when I turn 18, but I'm just wondering, how do vegans replace their dairy vitamins? How do vegans replace their dairy vitamins?they usually take multivtamnics/supplements to replace dairy

    they also drink soy milk//// and other soy productsHow do vegans replace their dairy vitamins?Excuse me? Dairy vitamins? Are we talking homogenized pus and pasteurized blood here? There are no nutrients to be found in cow's breast milk. Milk leeches calcium from your bones, which is why osteoporosis is so prevalent in America yet is almost nonexistent in Asia where dairy consumption up til the last decade was null.



    Dairy accelerates prostate cancer in men, so are you sure you want to hold off til your 18th?How do vegans replace their dairy vitamins?You simply don't need to. You can get all your nutrients from plant based foods. The one exception is B12, for which you can take a supplement or buy cereals and soymilk fortified with it. Milk is NOT a good source of calcium, and yes, it does contribute to osteoperosis. The best sources of calcium are from foods like broccoli, kale, almonds, etc. And eating foods with vitamin C really helps to absorb calcium. Taking a multivitamin is a good idea for most people, but it doesn't replace having a good diet. How do vegans replace their dairy vitamins?Well I'm vegan and I don't take any supplements. Only flax seed oil sometimes for the Omega 3's., but for dairy not. If you mean calcium we get the proteins and the calcium from soy milk, soy products such as soy yogurts, etc, vegetables like potatoes, broccoli, cauliflower, kale, and peanuts, walnuts etc :-)





    hope this helpsHow do vegans replace their dairy vitamins?What %26quot;vitamins%26quot; exactly are you talking about?

    Do you suppose its natural for humans to rely on drinking milk from another species, to get their essiential %26quot;vitamins%26quot;? Weren't we weaned when we grew teeth?

    Pasteurized cow milk is the one of the worst things you can put in your body under the so called %26quot;food%26quot; catagory. Its completely unnatural after its heated and loses most if not all its nutritional value. Not to mention all the enzymes that your body NEEDS to digest it! Because of the high protein content (and because its heated), everytime you drink it your body has to take away from it's own vital calcium, mineral, and enzyme supply just to digest it. It gives absolutely no benefit what so ever. Like I said your actually depleted of calcium when you drink it.

    It also creates mucus in the body, and leaves a nasty cote of unnatural muck in the digestive track.



    When milk is homogenized it does even more damage. It too is an unnatural process done only to %26quot;preserve%26quot; the life of the milk on the shelf, so profits aren't lost. It scars the arteries, which is one of the reasons heart disease is so present in people today.



    If your talking raw cow milk, that would be a different. But still the imbalance of minerals in cow milk are completely unnatural to the human body. Cow's milk was designed for calves, not humans. Just as human milk was created specifically for a human baby. Raw milk is extremely hard to find now days anyway, unless you have your own cows ofcourse or know someone who does.



    By the way, if your talking of vitamin B12, you don't need to seek animal products to get it. B12 is in leafy green vegetables, legumes and our own intesinal flora! It takes a healthy, clean digestive track to absorb it though. So most people who consume animal products don't even have the ability to absorb it, which is why B12 deficincy is more present in people who consume animal products than people who don't.



    Millions and millions of dollars are paid every year to keep the truth hidden from the public. Stop believing all these ads you see everywhere. They are not being put up by people who care for your health.How do vegans replace their dairy vitamins?Dairy is not hard to replace, nutritionally speaking.

    http://www.veganhealth.org/articles/bone



    I recommend that you try collards green with olive oil and balsamic vinegar.



    Bread, pasta, cereal, rice, beans, peas, lentils, nuts, seeds, fruits and veggies can easily offer everything that you need except B12.

    http://www.veganhealth.org/sh

    http://www.pcrm.org/health/veginfo



    All vegetarians should take a B12 supplement regularly since most people eat meat, dairy AND fortified cereals yet still have a B12 status that is lower than recommended.

    http://www.veganhealth.org/articles/b12



    It may help if you see proof that vegan people have the same potential as anyone else.

    http://sports.espn.go.com/espn/page2/sto

    http://www.veganbodybuilding.com/phpBB2/

    http://www.veganbodybuilding.com/phpBB2/

    http://www.macdanzig.net/bio.php

    http://www.scottjurek.com/career.php



    If you need meat or dairy during any stage of your life or to live any certain lifestyle, why does the American Dietetic Association say otherwise?

    http://www.eatright.org/cps/rde/xchg/adaHow do vegans replace their dairy vitamins?milk is just liquid fat with some vitamin d added



    wle
  • server
  • ittwit
  • How much to replace a tar and gravel roof?

    I have a small 1000 square feet house, with roof fairly flat, and I'd like to replace it with a material other than tar and gravel, yet low cost. Thanks.How much to replace a tar and gravel roof?A metal roof and you might not have to remove the old. That would be the cheapest and the metal roof has a great warranty. For more info check link.How much to replace a tar and gravel roof?You probably looking at $ 1200.00 - 2500.00 to replace it

    How do I replace my default picture with a avatar?

    I already had my avatar made, now I need to replace the default picture with the avatar.How do I replace my default picture with a avatar?on your YAnswers page, click on %26quot;My Profile%26quot; that's on the upper right side of the page. Then click on %26quot;edit my information%26quot;. ^_^

    It will take a few days and up to 2 weeks for your new avatar to show upHow do I replace my default picture with a avatar?note: blog mentions changing to profile images soon,

    http://yanswersblog.com/index.php/archiv…

    http://profiles.yahoo.com/

    ..

    ? to add picture or avatar here, jpg



    ? to use yahoo avatar, go to yahoo avatars, create character, for gender , select %26quot;preferences%26quot; on menu,

    http://avatars.yahoo.com/

    http://avatars.yahoo.com/avatar_towns.ht…



    ? to use yahoo 360 profile picture ,select %26quot;my page%26quot;

    http://360.yahoo.com/my_profile.html;_yl…



    ? then %26quot;edit personal photos%26quot; set,

    http://upload.360.yahoo.com/edit/photos.…

    choose photo as primary, save,



    http://360.yahoo.com/

    http://help.yahoo.com/l/us/yahoo/360/ind…



    ? then go to Y!A profile and edit, select and save,

    http://answers.yahoo.com/my/my_edit;_ylt…



    ???? ??

    ..

    How can I replace the stereo in my 1997 Lexus e300 with a new stereo head unit?

    I need to know if possible, how I can replace the old stereo in my car. I found a great deal on this stereo and before I buy it I want to know if it will be able to fit in my car and how to do it. The old stereo is double-din.How can I replace the stereo in my 1997 Lexus e300 with a new stereo head unit?go to best buy if it can be done they will know

    How much to replace a throttle position sensor on a 96 grand am?

    I am buying the part online and I now it doesn't take long at all to replace one. But how much do you think most places would charge for labor?How much to replace a throttle position sensor on a 96 grand am?a shop will charge you a minimum rate of probably 1/2 to an hour at shop rates. Call around for a free estimate. About $60-80How much to replace a throttle position sensor on a 96 grand am?should take 2 seconds, but then you have to position it correctly to make sure your getting the right voltage...maybe another 2 seconds for thatHow much to replace a throttle position sensor on a 96 grand am?DO it yourself. It's FREE!!!! SImple job. The new part should have instructions with it. LEARN!!!

    How much would it cost to replace the clutch?

    I'm looking at a 1993 Honda Del Sol, but when i took it for a test drive I could feel the throw out bearing and hear it. How much would it cost to replace it, and would it be cheaper to just replace the whole clutch?How much would it cost to replace the clutch?the thorow out bearing usually come with the clutch kit. clutch is coming out when you do the throw out bearing so why put the old one back in?? on a del sol i would estimate $800 on a shop to repalce it unless you doit your self.How much would it cost to replace the clutch?it would not be cheaper to replace the 500 dollar clutch than the 50 dollar bearing



    however as it costs 300 or so to remove engine or tranny to replace either the saying goes..[as long as its apart you may as well do the whole thing] cost about 800
  • 4how can i get my ex back
  • density of virgin coconut oil
  • How to replace brake master cylinder on 1998 ford explorer?

    I replaced brake pads on front and back. I replaced caliper where needed and bled lines. I don't have leak. Can I check master cylinder or do I replace it? If so, HOW? ThanksHow to replace brake master cylinder on 1998 ford explorer?What is the problem?? Someone could help you better if we knew the problem.

    How do you replace the belt that drives only the power steering fluid pump on a 2000 chrysler cirrus?

    This car has a two-belt system. One only drives the power steering fluid pump and is the one I am trying to replace. There is no belt tensioner so I do not know how to get the belt over the pulleys.How do you replace the belt that drives only the power steering fluid pump on a 2000 chrysler cirrus?What engine do you have. If it is the 2.4l the pump is in the front if its the V6 its in the back. The belt tension is applied by moving the PS pump on its mount. On a V6 vehicle you will have to raise it up to get under the passenger side of the engine to access the mount bolts to adjust it. On the 2.4L it is right there on the top.

    How do I replace a fuel pump in a Mercruiser 898 sterndrive?

    I have a 1978 Mark Twain 180v, with a Chevy 305 cid on a Mercruiser 898 Sterndrive. The fuel pump is out and I need to replace. My only problem is that I have no idea how and do not have a manual. If anybody can help, please do.How do I replace a fuel pump in a Mercruiser 898 sterndrive?The same way as on a 305 or 350 chevy car engine.

    Gasket on surface, pump lever in the block and tilt the pump so the lever goes under the cam lobe, tighten the bolts and reconnect the lines.

    One note: be sure NOT to use a car fuel pump, the marine version has an extra port (diaphragm vent) that routes by a fuel hose to the carburetor top, when the diaphragm in the pump fails and it starts to leak this extra port dumps the fuel into the carb instead into the boat!How do I replace a fuel pump in a Mercruiser 898 sterndrive?When U remove it the rod will slid down U will have to lift it up and hold it so the arm on the pump pushes it up if not the pump will not work and damage will incur.How do I replace a fuel pump in a Mercruiser 898 sterndrive?frank m nailed it.



    follow the fuel hose down from the carb. you'll find a pump on the side of the motor with 2 bolts holding it on.

    unbolt it, clean the old gasket off the motor and install the new one with a new gasket.



    as frank said, you need a MARINE pump, not one purchases at an auto parts store. an automotive pump is not designed with the same thoughs of fumes and fire as a marine pump is.



    on a big block chevy, you would however need to worry about a push rod between the pump and the cam that drives it. but not on a small block, such as a 305.

    How much would it cost to replace the motor in a 98 Toyota corolla?

    My car recently died, and I am debating whether to spend 2-4k on some marginal used car or if it would be better to buy a used engine and replace it in the car--



    My car is a junker already anyway(it was my first car since 16 and I am now 24).



    How much do you think it would cost to replace the motor, including the price of the motor?How much would it cost to replace the motor in a 98 Toyota corolla?I'd suggest buying a Honda Civic or Accord, for $4000.How much would it cost to replace the motor in a 98 Toyota corolla?Depending on where you live - rebuilt engines can run from $500 to $1000 installed - check around for best price %26amp; (!!!) a warrantyHow much would it cost to replace the motor in a 98 Toyota corolla?4 grandHow much would it cost to replace the motor in a 98 Toyota corolla?You sure got your moneys worth there.



    Sell the Corolla for parts. Take that money and add it to what you've

    got towards a newer Toyota and your set....



    I'm sure you know what the good parts are, even some you wouldn't

    even think. ie...tail lights, electrical, glass, etc...



    If the car is really far gone.....Send it to the salvage yard and get

    the scrap metal price for it...



    Good Luck with the new wheels..



    OH, FORGET ABOUT A MOTOR, IT'S JUST NOT WORTH IT.



    95 Camry Owner..How much would it cost to replace the motor in a 98 Toyota corolla?Junk it and buy a new used car...hey...it's new to you.



    Not sure what you can get for 4k but I think you could find a ford focus 3 door...better than nothing.

    How do I replace the side mirror on driver's side of 92 minivan?

    I have a 92 Plymouth Voyager minivan and need to replace the driver's side mirror. Do I need to take the door apart to do this? If so, how do I do that?How do I replace the side mirror on driver's side of 92 minivan?i think on that you will have to pull the door panel. there are clips around the outer edge of the door panel and screws on the door pull. remove the screws and pry the panel away with a screwdriver to unclip the panel.then there will be 2 or 3 10 mm bolts holding the mirror on remove those and reverse procedure to pu back togrether. Good luckHow do I replace the side mirror on driver's side of 92 minivan?the inside door panel has to come off or at least loose enough to be able to get to the nuts that hold the mirror on.
  • work for data entry from
  • desktop issue
  • How much will it cost to replace the suspension on a 1997 infiniti qx4?

    I know it depends on what is being replaced but I just want a ballpark figure if I replace the most common things.How much will it cost to replace the suspension on a 1997 infiniti qx4?Rear shocks for your vehicle are about $50 each: ($100)



    Front struts for your vehicle are about $100 each: ($200)



    A set of 4 coil springs is probably about: ($400)



    Probably 4-6 hours of labor. Assuming an average shop rate of $60/hr: ($240 - $360)



    Total Estimate: $940 - $1060



    You could cut this cost down by buying cheaper suspension parts (the low-end Monroe shocks and struts are about 30% cheaper), but I can't recommend it if you plan on keeping the vehicle.



    Also note that any problems during the install that are due to worn or frozen bushings is going to increase the cost of parts as well as labor, and it will add up quickly. Don't be surprised if the shop recommends new ball joints, suspension end links, bushings, camber kits or suspension mounts, all of which significantly increase time and cost.How much will it cost to replace the suspension on a 1997 infiniti qx4?Of course once you get all the following replaced mentioned above you would defently need an alignment,to make sure the parts are all working together.Anytime you replace something in the suspention its always recommended to get a alignment and usualy they run $60 bucks but i would defently take it in and see what they say needs replaced i find it hard to beleive the complete suspention system is shot.normally its shocks and stuts, the coil springs control the vechile height , ball joints can go bad most of these you can test your self or have a shop test out .How much will it cost to replace the suspension on a 1997 infiniti qx4?yes.How much will it cost to replace the suspension on a 1997 infiniti qx4?whatever you do dont take it to the dealer and make sure you check online for savings. Mine costed about 1600How much will it cost to replace the suspension on a 1997 infiniti qx4?It would probably cost more than the car is worth.....time to go car shopping.

    How do I replace the retaining spring on my Mazda MPV headlight?

    My MPV headlight lamp was changed for me, but they took out the retaining clip completely instead of just swinging it out of the way. Now I can't figure out how to replace it. Any tips?



    They removed the retaining clips on both sides, so I can't look at one installed correctly to see how to do it. I'd really love it if anyone could post a picture of what it should look like when installed, then I could figure it out from there. Thanks!How do I replace the retaining spring on my Mazda MPV headlight?there is no photo for that it has 2 cross screws you have to take them out and place the spring in position without let it fall into the lamp or you will have some serious problem



    best advice is taking the lamp out and you have to remove the front bumper to make so



    not an easy task...

    How do I replace a power cord in a toaster?

    I need to replace damaged power cord in my toaster / sandwich maker. It has three wires coming out of the inside: red, green and blue. The wires in the power cord are brown, blue and yellow-green. Which wires in the toaster should be connected to which ones in the power cord?How do I replace a power cord in a toaster?it would be less expensive to buy a new toasterHow do I replace a power cord in a toaster?Call Home Depot or a store like them that gives advice over the phone.



    Otherwise, it may be cheaper to buy a new toaster/sandwich maker instead.



    Hmm. Strangely, I am now craving a grilled cheese sandwich. ;)How do I replace a power cord in a toaster?The two green ones are the grounds, and they'll go together. The others don't sound standard. I'd put the two blue ones together, and the remaining two together. Stand back and plug it in! There aren't many ways to do this wrong. :)How do I replace a power cord in a toaster?call a professional to do it because it needs to be opened up and replace the cord from the inside by soldering it.